ISO/TS TECHNICAL SPECIFICATION 13399-301 First edition 2013-10-15 Cutting tool data representation and exchange - Part 301: Concept for the design of 3D models based on properties according to IsO/ TS 13399-3: Modelling of thread- cutting taps, thread-forming taps and thread-cutting dies Representation et échange des donnees relatives aux outils coupants Partie 301: Description des modeles 3D baseés sur les propriétes de I'S0/TS 13399-3: Modelisation des tarauds, tarauds a refouler et filieres de filetage Reference number IS0/TS 13399-301:2013(E) LSO @ IS0 2013 icense from IHS Not for Resale IS0/TS 13399-301:2013(E) COPYRIGHTPROTECTEDDOCUMENT ISO2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISOcopyrightoffice Case postale 56:CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax +4122 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ IS0 2013 - All rights reserved No reproductic networking permitted without license from IHS Not for Resale IS0/TS 13399-301:2013(E) Contents Page Foreword ..V Introduction. ..vii 1 Scope. 2 Normative references ..1 3 Starting elements, coordinate system, planes 3.1 General. .1 3.2 Reference system. 3.3 Coordinate system at the cutting part .2 3.4 McScoordinatesvstem 3.5 Planes .3 4 Design of the model .4 4.1 General ..4 4.2 Necessary parameters for the connection interface feature ..5 5 Thread-cutting tap with offset shank .5 5.1 General .5 5.2 Necessary properties. .6 5.3 Geometry of the non-cutting part including the shank .6 5.4 Geometry of the cutting part. .7 5.5 Thread-cutting tap with offset shank - Complete ..8 6 Thread-cutting tap with reinforced shank .9 6.1 General. .9 6.2 Necessary properties.. .9 6.3 Geometry of the non-cutting part including the shank .10 6.4 Geometry of the cutting part ..10 6.5 Thread-cutting tap with reinforced shank complete .10 > Thread-forming tap with offset shank .11 7.1 General .11 7.2 Necessary properties .11 7.3 Geometry of the non-cutting part including the shank ..11 7.4 Geometry of the cutting part. ..12 7.5 Thread-forming tap with offset shank - Complete ..12 8 Thread-forming tap with reinforced shank .12 8.1 General. ..12 8.2 Necessary properties. .13 8.3 Geometry of the non-cutting part including the shank .13 8.4 Geometryofthecuttingpart .13 8.5 Thread-forming tap with reinforced shank - Complete .13 9 Thread-cutting die round shape .13 9.1 General ..13 9.2 Necessary properties ..14 9.3 Geometry of the non-cutting part ..14 9.4 Geometry of the cutting part. .15 9.5 Thread-cutting die, round shape - Complete ..16 10 Thread-cutting die, hexagonal shape .17 10.1 General. .17 10.2 Necessary properties. .17 10.3 Geometry of the non-cutting part ..18 10.4 Geometry of the cutting part .18 10.5 Thread-cutting tap, hexagonal shape - Complete. ..18 11 Design of details .19 iii nse with ISt ed without license from IHS Not for Resale