ISO INTERNATIONAL STANDARD 9473-2 First edition 2006-04-01 Textile machinery and accessories - Strip steel for dents of reeds - Part 2: Hardened strip steel Materielpour I'industrie textile-Feuillards d'acierpourdents de peignes Partie2:Feuillards d'aciertrempé Reference number ISO 9473-2:2006(E) @ISO2006 ISO9473-2:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation @ISO2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either iSO at the address below or ISO's member body in the country of the requester. ISO copyright office Casepostale 56.CH-1211Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ISO9473-2:2006(E) Foreword IsO (the International Organization for Standardization)is a worldwidefederation of national standards bodies (Iso member bodies). The work of preparing International Standards is normally carried out through IsO International Electrotechnical Commission (IEC)onall matters ofelectrotechnical standardization. International Standards are drafted in accordance with the rules given in the IsO/lEc Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. rights. IsO shall not be held responsible for identifying any or all such patent rights. IsO9473-2 was prepared by Technical Committee ISO/Tc72,Textile machinery and accessories, Subcommittee Sc 3,Machineryforfabricmanufacturing includingpreparatorymachineryandaccessories. This first edition of ISO 9473-2, together with ISO 9473-1, cancels and replaces ISO 9473:1988, of which it constitutes a technical revision. Iso 9473 consists of the following parts, under the general title Textile machinery and accessories - Strip steel for dents of reeds: Part 1: Cold rolled strip steel Part 2:Hardened strip steel INTERNATIONALSTANDARD ISO9473-2:2006(E) Textile machinery and accessories Strip steel for dents of reeds Part 2: Hardened strip steel 1 Scope This part of Iso 9473 specifies the dimensions and the designation of hardened strip steel used to manufacture dents of reeds, according to ISO 366-1, Iso 366-2, IsO 366-3, and ISO 366-4. 2Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)applies. Iso366-1,Textilemachineryand accessories-Reeds-Part1:Pitchbound reeds—Dimensions Dimensionsanddesignation Dimensionsanddesignation Iso366-4,Textile machinery and accessories- Reeds- Part4:Dimensions and designation of plastic-bound metal reeds Iso366-5,Textilemachineryand accessories-Reeds-Part5:Dimensions and designationof profile capsules 3 Dimensions The dimensions of hardened strip steel for dents of reeds shown in Figure 1 are given in Table 1. The dimensions (height, width and dent width) shall be subject to an agreement between the interested parties and in respect of the