ISO INTERNATIONAL STANDARD 8940 Second edition 2002-08-01 Aerospace Nuts, anchor, self-locking, sealing, floating, two-lug, with counterbore, with MJ threads, classifications: 9oo MPa (at ambient temperature)/120 °C, 900 MPa (at ambient temperature)/175 °C and 900 MPa (at ambient temperature)/235 °C - Dimensions Aéronautiqueetespace- Ecrous a river, a freinage interne, étanches, flottants,doublepatte,avecchambrage,afiletageMJ,classifications: 900MPa (atempératureambiante)/120°C,900MPa (atempérature ambiante)/175°Cet900MPa(atempératureambiante)/235°C- Dimensions Reference number ISO 8940:2002(E) @ISO 2002 copyrighted by UNE, C/ Genova, 6. 28004 Madrid, Sps 8 00:45:13 UTC 2024 ISO 8940:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. @ISO2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic in the country of the requester. ISO copyright office Case postale56CH-1211Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.ch Printed in Switzerland i @ISO2002-All rightsreserved copyrighted by UNE, C/ Genova, 6. 28004 Madrid, Spain (all rights reserved); Sun Feb 18 00:45:13 UTC 2024 Downloaded/printed for Georgia Institute of Technology, This standard provided by AENOR. No further reproductions authorized. ISO8940:2002(E) Foreword ISO (the International Organization for Standardization) is a worldwidefederation of national standards bodies (isO committees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhas liaison with IsO, also take part in the work. IsO collaborates closely with the International Electrotechnical Commission(iEC)onallmattersofelectrotechnicalstandardization InternationalStandardsaredraftedinaccordancewiththerulesgivenintheISO/lECDirectives,Part3 The main task of technical committees is to prepare International Standards.Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approvalbyat least 75%of the memberbodies castinga vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 8940 was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles, Subcommittee SC 4, Aerospacefastenersystems. This second edition cancels and replaces the first edition (IsO 8940:1988), which has been technically revised ii ISO8940:2002(E) Introduction The dimensions specified in this International Standard have been determined to allow production of a part which will satisfy the requirements of the procurement specification IsO 5858. iv @ ISo 2002 - All rights reserved C copyrighted by UNE, C/ Genova, 6. 28004 Madrid, Spain (all rights reserved); Sun Feb 18 00:45:13 UTC 2024 Downloaded/printed for Georgia Institute of Technology, This standard provided by AENOR. No further reproductions authorized. INTERNATIONALSTANDARD ISO 8940:2002(E) Aerospace Nuts, anchor, self-locking, sealing, floating, two-lug, with counterbore, with MJ threads, classifications: 9oo MPa (at ambient temperature)/120 °C, 900 MPa (at ambient temperature)/175 °C and 900 MPa (at ambient temperature)/ 235°cDimensions 1 Scope This International Standard specifies the