EN ISO8496 EUROPEANSTANDARD NORMEEUROPEENNE EUROPAISCHENORM November2013 ICS 77.040.10 Supersedes EN ISO8496:2004 English Version Metallic materials - Tube - Ring tensile test (ISO 8496:2013) Materiaux metalliques -Tubes -Essai de traction sur Metallische Werkstoffe-Rohr- Ringzugversuch (ISO anneaux (ISO 8496:2013) 8496:2013) This European Standard was approved by CEN on 28 October 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Siovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPAISCHES KOMITEE FUR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels @2013CEN All rights of exploitation in any form and by any means reserved Ref.No.ENISO8496:2013E worldwide for CEN national Members. ENISO8496:2013 (E) Foreword This document (EN ISO 8496:2013)has been prepared by Technical Committee ISO/TC 164"Mechanical fittings” the secretariat of which is held by UNI. textorbyendorsement,atthelatestbyMay2o14,andconflictingnationalstandardsshallbewithdrawnatthe latestbyMay2014 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent This document supersedes EN ISO 8496:2004. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Endorsementnotice The text of ISO 8496:2013 has been approved by CEN as EN ISO 8496:2013 without any modification. IS0 8496:2013(E) Contents Page Foreword iv Scope. 1 .1 2 Principle. .1 3 Apparatus. .1 4 Test piece. .2 5 Procedure. .2 6 Test report. 2 @ IS0 2013 - All rights reserved ii IS0 8496:2013(E) Foreword Iso (the International Organizationfor Standardization)is a worldwidefederation of national standards bodies (IsO member bodies).The work of preparing International Standards is normally carried out through Iso technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with Iso, also takepart in the work. ISo collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the Iso/IEC Directives, Part 1.In particular the different approval criteria needed for the different types of Iso documents should be noted. This document was drafted in accordance with the editorial rules oftheISo/IEC Directives, Part 2.www.iso.org/directives Attention is drawn to thepossibilitythat some ofthe elements of this documentmaybethe subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will