ISO INTERNATIONAL STANDARD 7682 Second edition 2003-11-15 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Acrylonitrile-butadiene-styrene (ABS) Systemesdecanalisations enplastiquepourI'évacuationdes eaux- vannes etdes eaux usées (a basse eta haute température)a I'interieur desbatimentsAcrylonitrile-butadiene-styrene(ABS) Referencenumber ISO 7682:2003(E) ISO @ISO2003 ISO7682:2003(E) PDFdisclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. @ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either Iso at the address below or ISO copyright office Case postale 56: CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland !! @ISO2003—Allrightsreserved ISO 7682:2003(E) Contents Page Foreword Introduction 1 Scope. 2 Normativereferences 3 Symbols andabbreviations 4 Material 5 General characteristics 9 Geometrical characteristics Mechanical characteristics ofpipes 7 21 8 Physical characteristics 23 9 Performance requirements .24 10 Sealing rings 11 Adhesives.. .25 12 Marking... 25 13 Installationofpipingsystems 26 Annex A(informative)Additional characteristics of ABS pipes andfittings Bibliography . ISO7682:2003(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standards bodies non-governmental, in liaison with IsO, also take part in the work. isO collaborates closely with the International Electrotechnical Commission (IEC)onallmatters of electrotechnicalstandardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. transport offluids, Subcommittee Sc 1,Plastics pipesandfittings for soil, wasteand drainage (including land drainage) This second edition cancels and replaces the first edition (isO 7682:1991), which has been technically revised ISO7682:2003(E) Introduction EN 1455-1 which are applicable to those pipes and fittings which, according to EN 1455-1, are intended to be used inside buildings (application area code“B", see EN 1455-1) only. ISO 7682:2003(E) INTERNATIONALSTANDARD Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Acrylonitrile-butadiene- styrene (ABS) Scope This International Standard specifies the requirements for solid-wall acrylonitrile-butadiene-styrene (ABS) pipes and fittings for soil and waste discharge (low and high temperature) above ground inside buildings, as well as the system itself. It does not include buried pipework. It also specifies the test parameters for the test methods referred to in this International Standard. This International Standard is applicab