ISO INTERNATIONAL STANDARD 21111-10 First edition 2021-10 Road vehicles In-vehicle Ethernet : Part 10: Transport layer and network layer conformance test plans Vehicules routiers -Ethernet embarqué- Partie 10: Plans de test de conformite des couches transport et reseau Reference number ISO 21111-10:2021(E) ISO @IS02021 IS0 21111-10:2021(E) COPYRIGHT PROTECTED DOCUMENT @IS02021 All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, withoutpriorwrittenpermission.Permission can berequestedfrom eitherIso at theaddress below orIso'smemberbodyinthecountryoftherequester. ISO copyright office CP 401 · Ch. de Blandonnet 8 CH-1214 Vernier, Geneva Phone: +4122 749 0111 Email: [email protected] Website: www.iso.org Published in Switzerland ii @ IS0 2021 - All rights reserved IS0 21111-10:2021(E) Contents Page Foreword .V Introduction. .vi 1 Scope. 1 2 Normative references .1 3 Terms and definitions .1 4 Symbols and abbreviated terms. .2 4.1 Symbols. 2 4.2 Abbreviated terms 2 5 Conventions 4 6 CTP test system set-up and CTC structure .4 6.1 General. .4 6.2 Test system set-up 5 6.3 CTC definition 6 6.4 Terminology used in CTCs. 7 6.5 IUT prerequisites - TCP/IP TestStub. 7 6.5.1 General 7 6.5.2TCP/IP TestStub service primitives 7 6.5.3 Result codes 8 7 Network and transport layers CTCs .8 7.1 NL - Address resolution protocol (ARP) 8 7.1.1 General .8 7.1.2 Referenced specification .8 7.1.3 Test system topology - NL - ARP 8 7.1.4 Test system topology and related CTC configuration .9 7.1.5 CTC ARP overview. 9 7.1.6 ARP parameters used in CTCs. 10 7.1.7 ARPCTCs 11 7.2 NL - Internet control message protocol version 4 (ICMPv4) 42 7.2.1 General 42 7.2.2 Referenced specification. 42 7.2.3 Test system topology - NL - ICMPv4. 42 7.2.4 Test system topology and related CTC configuration 43 7.2.5 ICMPv4 parameters used in CTCs. 43 7.2.6 ICMPv4 CTCs 44 7.3 NL - Internet protocol version 4 (IPv4) 54 7.3.1 General 54 7.3.2 Referenced specification 54 7.3.3 Test system topology - NL - IPv4 54 7.3.4 Test system topology and related CTC configuration 55 7.3.5 IPv4 parameters used in CTCs.. 55 7.3.6 IPv4 CTCs 56 7.4 NL - Dynamic configuration of IPv4 link local address. 82 7.4.1 General 82 7.4.2 Referenced specification 82 7.4.3 Test system topology - NL - Dynamic configuration of IPv4 link local address. 82 7.4.4 Test system topology and related CTC configuration. 83 7.4.5 Dynamic configuration of IPv4 parameters and constants used in CTCs 83 7.4.6 IPv4 autoconf CTCs 84 7.5 TL - User datagram protocol (UDP) .117 7.5.1 General .117 7.5.2 Referenced specification .117 @ IS0 2021 - All rights reserved iii IS0 21111-10:2021(E) 7.5.3 Test system topology - TL - UDP .118 7.5.4 Test system topology and related CTC configuration 118 7.5.5 UDP parameters used in CTCs.. .118 7.5.6 UDP CTCs .119 7.6 TL - Transmisison control protocol (TCP) .137 7.6.1 General .137 7.6.2 Referenced specification. .138 7.6.3 Test system topology- TL - TCP .138 7.6.4 Test system topology and related CTC configuration ..138 7.6.5 TCP parameters used in CTCs .138 7.6.6 TCP CTCs. .139 Bibliography. 205 iv @ IS0 2021 - All rights reserved IS0 21111-10:2021(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (IsO member bodies). The work of preparing International Standards is normally carried out throughIsotechnicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with Iso, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardi